Miller350z Posted October 28, 2016 Share Posted October 28, 2016 Hi all, well my 350 is a little poorly. I drove it out of the garage today, all as normal but then when I went down the road and put the car under load i got some bad vibrations from the rear of the car. Felt like near side rear. I thought what was that, took my foot off the throttle put it on again and bad vibration, the car wasn't accelerating and the malfunction indicator light came on solid for about a mile then went off. The best way I can describe it is say the teeth on the drive shaft were worn, it's ok with little throttle but then when you put it under load it's like the teeth are slipping causing the vibration and lack of drive. I do not have a clue really what it could be so hope someone can help me out. Thanks a lot Sent from my SM-G930F using Tapatalk Quote Link to comment Share on other sites More sharing options...
Payco Posted October 28, 2016 Share Posted October 28, 2016 I am sure someone will be along soon to help but try sending ZMANALEX a pm. Hope its nothing serious and you get it sorted. Quote Link to comment Share on other sites More sharing options...
Miller350z Posted October 28, 2016 Author Share Posted October 28, 2016 Thanks, yeah I hope so too. I'm now thinking could it be clutch as that would explain the lose of drive but would that cause the the vibrations at the rear? ? Or I'm thinking could it be differential bushes? Hope someone who has had the same thing or just someone who knows what it could be let me know Sent from my SM-G930F using Tapatalk Quote Link to comment Share on other sites More sharing options...
GreenLandy Posted October 28, 2016 Share Posted October 28, 2016 Drive shaft, wheel bearing, prop UJ joint(s), wheel not on tight enough, diff worn, all manner of bushes knackered and so on Best bet is to take the wheel off and see what you can find Quote Link to comment Share on other sites More sharing options...
Miller350z Posted October 28, 2016 Author Share Posted October 28, 2016 Right for about a week now there has been a rattle from the rear. Then a vibrating noise from the rear when releasing the clutch....let's say the biting point when it's just being released. Then this has happened today and instead of a slight vibration it's now a violent vibration and doesn't go anywhere if the car is put under any kind of load. Engine revs fine whilst in neutral Sent from my SM-G930F using Tapatalk Quote Link to comment Share on other sites More sharing options...
Keyser Posted October 28, 2016 Share Posted October 28, 2016 (edited) Could it be that the DMF is dead then? maybe the springs have gone in it, thrust bearing (spigot bearing) would now be worn as well or maybe the clutch plate itself has shattered, I'd be inside that gearbox to have a look if those symptoms were on my car, Possibly the prop shaft UJ as mentioned above but a, that's easy to look at and b. the prop shaft would be on the floor if it had become that much worse. if it is axle tramp then as above you need to look at the diff bushings and the rear gearbox bush. Good luck Edited October 28, 2016 by Keyser Quote Link to comment Share on other sites More sharing options...
Miller350z Posted October 28, 2016 Author Share Posted October 28, 2016 None of which sound good. I've just finished work and now the malfunction indicator light is constantly on and she's running rough so that's one more problem to solve. I've parked it in the garage now so it'll stay there for the weekend. Guess I need to clear the engine fault light then go through and check for the other problems. Thanks all for the info. Hopefully have it sorted sometime next week Sent from my SM-G930F using Tapatalk Quote Link to comment Share on other sites More sharing options...
Keyser Posted October 28, 2016 Share Posted October 28, 2016 Points me back at clutch if it is shaking really bad then the cps maybe getting a bad signal. Quote Link to comment Share on other sites More sharing options...
catman Posted October 29, 2016 Share Posted October 29, 2016 When you say that the car "goes nowhere" when you try to accelerate, do the engine revs increase? if not, then the clutch isn't slipping. Tim Quote Link to comment Share on other sites More sharing options...
Stutopia Posted October 29, 2016 Share Posted October 29, 2016 Suggest you start with pulling the code form the CEL and finding what it is, rather than clearing it. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.