Zeezeebaba Posted December 4, 2015 Share Posted December 4, 2015 The previous owner of my Z installed brows paint matched to the car. I didn't mind them but noticed the lens underneath were trapping heat and starting to damage the surface of the lights. Today I removed them and by christ were they bodged on. The putty like substance was easy to remove but what appears to be superglue type stuff was also present. After a good clean I still have glue on the light cover one side and was wondering what sort of solvent destroyer would sort it. I need to be careful as it may have eaten into the cover a little. Oh and if anyone wants a free pair of GM brows they can have them Quote Link to comment Share on other sites More sharing options...
mdunbar Posted December 4, 2015 Share Posted December 4, 2015 Nitro Mors is great, but may also damage the lens in this instance. Quote Link to comment Share on other sites More sharing options...
ZEUS Posted December 4, 2015 Share Posted December 4, 2015 Christ don't use Nitromors it will melt the plastic lens! Try white spirit to start with or meths on a cloth. If that fails and it is super glue you could try chipping it off or failing that fine wet n dry. Quote Link to comment Share on other sites More sharing options...
gillywig2 Posted December 4, 2015 Share Posted December 4, 2015 Petrol or lighter fluid will dissolve the glue residue. Quote Link to comment Share on other sites More sharing options...
Hodaka Posted December 4, 2015 Share Posted December 4, 2015 Oh and if anyone wants a free pair of GM brows they can have them If they're still available, please could I have them? Quote Link to comment Share on other sites More sharing options...
Payco Posted December 4, 2015 Share Posted December 4, 2015 I would get a headlight restoration kit for £20 or so and go through the sanding/polishing step by step process. It will kill two birds with one stone and restore your headlights too. Good luck. Quote Link to comment Share on other sites More sharing options...
Zeezeebaba Posted December 4, 2015 Author Share Posted December 4, 2015 Oh and if anyone wants a free pair of GM brows they can have them If they're still available, please could I have them? PM sent 1 Quote Link to comment Share on other sites More sharing options...
Exec Posted December 4, 2015 Share Posted December 4, 2015 I'm with Payco on this one - sand it with a VERY fine grit paper and then polish it with a buffing pad on a drill or buffer & then seal with something... the kit is probably your best bet. 1 Quote Link to comment Share on other sites More sharing options...
Zeezeebaba Posted December 4, 2015 Author Share Posted December 4, 2015 (edited) Sod it I'm just going to get facelift bi xenons instead. I've now used a fine cutting compound but it looks like one small spot has been damaged by the glue so further cutting is pointless.A shame as the rest of the lights are fine bar one inch and a half patch where the glue has eaten the cover. Thanks for the input guys. Edited December 4, 2015 by Zeezeebaba Quote Link to comment Share on other sites More sharing options...
buster Posted December 4, 2015 Share Posted December 4, 2015 i ve got a pair of o/e 54plate headamps sat in the garage which have beed stripped of the ballast and bulb wiring.....open to offers.was holding just in case i needed them as spares but sounds you need them more than me. Quote Link to comment Share on other sites More sharing options...
veilside z Posted December 4, 2015 Share Posted December 4, 2015 So annoying Hope you get sorted Quote Link to comment Share on other sites More sharing options...
Zeezeebaba Posted December 4, 2015 Author Share Posted December 4, 2015 Cheers for the offer mate but I'm going to hold out for some facelift ones I think. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.