wilo

any tips on getting the old stuff off ? i recon ill nacker the door cards up taking it off as its like concrete to remove

shame its 10th - 19th for delivery otherwise price is mint.also how do you tighten a round cap properly

just over tightened my oil fill cap and now it clicks past and goes slack again . any advise on where to purchase a replacement appreciated. looked on ebay but can only find those alloy types that dont look very good build quality and take a week or more for delivery

ill get some pics up in 5 mins

need some advice please . i have noticed that some areas of my interior flocking has come away or going very thin. whats the best way to fix this ? i have seen flock kits on ebay that consists of flock fibres and glue but my flocking looks like it was sheet form as it comes away and is intact in large pieces . tried removing the remaining from the door cards but its solid and seems impossible to remove ....any tips guys

I've messaged him with interest in the zed and asked " what engine modifications have you done to get 380bhp" his reply was ....."i have checked 340 thanks" . so its actually lost 40bhp in less than 12 hours :/

as TT said .i repeated the process 4 times leaving a 1 second interval between each

iv just done the ignition trick and it worked. hope it stays off as I've been reading it can come back . checked under seat and all wiring seams fine ..there's nothing under there that shouldn't be there either . also checked passenger seat belt to see if pre tensioner was engaged but that's fine also

no not the esp..i put that off lol. its the airbag one ..no one touched or banged out as far as i know

looks light seatbelt warning with air bag ....both my self and passenger were wearing the belts Sent from my SM-G935F using Tapatalk

just posted about a problem and another just cropped up.just took car out and this warning light keeps flashing

cheers ricky ill give it a go.any ideas where to get one

okay guys iv waited two weeks to post this as at first I thought i was going nuts . i check my oil level every few days and top up once a week to keep it at max. a couple of times iv gone to losen the oil filler cap only to find its already loose even though i do it up tight everytime. just been out to clean the car and top up the oil as I've been on a long run today only to find the cap was practicaly fully undone basically on its last thread. any ideas as to whats going on ?

haha never thought of that tbh. Sent from my SM-G935F using Tapatalk

yes i have a place local that mixes paint but there wv2 is more silvery than my paint work and the halfords stuff is to dark. im thinking of having the bumper wrapped if i can get the wrap in the correct colour

ahh cheers wondered what the P was for.and yea I've tried finding a garrage in my area with a paint scanner but non round these parts as far as i know What is it your need painted? just a few small stone chips in bumper ..nothing major but i know there there so bugs me .was looking for a touch up pen in the correct tint of wv2

ahh cheers wondered what the P was for.and yea I've tried finding a garrage in my area with a paint scanner but non round these parts as far as i know

having a real problem getting a colour match for my 04 DE . tried 2 places using the vin code wv2 but one was too dark and the other was too silver. just noticed on my vin theres a leter P after the WV2 code . is this a shade ? and is it possible to get this exact tint/ shade of WV2?

hi guys needing some advice please. front / rear pads are due to be done and looking for something thats good for fast road use and minimal dust as i have white alloys which are a pita to keep clean. car is a 04 DE and has brembos . also needing handbrake shoes so any link's to a full set would be appreciated .

You get instructions and all the fittings needed buddy, no need for anything else cheers will be ordering next week .

yea at some point ..should be ordering the plenum next week once iv sorted fitting with the garrage . already got a full decat milltek system and ramair induction so remap will definitely be on the cards . if i can make 300bhp ill be happy tbh

yea im very heavy handed tbh..break out i touch and thx iv seen the video

damn looks like ill have to try find a company that custom makes badges

okay thx for the heads up ,would you consider selling me them at all

also looking for someone that can custom make 3d badges as i have one in mind that i would like making