Randy_Baton

I've got a set for sale, link in my signature. I brought a set painted them and I'm now selling my old pair. Unless you live near one if the zed sheds a spare set may be hard to come by.

Where are you located? Might be a member/trader close by

Do you have any details on the dipped centre console, I take it was black base coat then a gloss finish but it really pops so was wondering if there is some other color going on in there

I'll have the card on dipped DE one. I've got a build thread so no problem with providing pictures Just pm me the details

Waited 2.5 hours for the most uninterested repair guy. He tried to tell me the resivouir had probably cracked. So I unscrewed the bolt and showed it hadn't. Then told me my vehicle was too large for him to tow and because it was rwd he'd need a longer tow bar? He then said it would be another 2 hours for a recovery vehicle! I at least got him to refill the coolant which he did but said his coolant was a bit watery, which was nice! Waited 2 hours got, bored and drove round the block a few times. No issues so I drove home in the dark and rain, everything was fine. Looks like I'll need to give the motor a clean or pop up to the Cougar store.

Hopefully getting recovered to japex.

Okay I'm learning stuff. Turned the engine on and AC on and only the passenger side fan was turning. I gave the driver side one a spin and it started running. Does this mean the driver side one is bad?

How do I check the fans. I've let it cool down and turned the engine on to idle. Oil temp is about 15 and engine temp seems to be holding steady Just before this happens I did over rev in first for about 30 seconds moving in slow traffic and trying to plug in a charger.!

I'll let the repair man fix it

Temp gauge was in the red. Coolant has dropped below min. Is it drivable? I'm in Weybridge on the way to Birmingham.

Hi just driving along in slow traffic and I notice white smoke coming out from the bonnet. Pop the bonnet and the coolant is boilng over. So at least it's steam and not smoke. I've let it cool off but what do I do? The oil gauge had dropped to zero as well

Well put me down for a carbon wrapped DE one then.

Just noticed on the group buy you are doing DE. Would have brought one months ago if I'd known I posted on the font page then realised they were only for HR. I should of just asked! Pm me the details. Might be a good idea to change the name of the thread to HR /DE

You can even get a taxi ride from Prime in America http://www.azfamily.com/news/Optimus-Prime-to-roll-out-with-Uber-users-in-Phoenix-263498521.html

I've got one for sale, the link is in my signiture

the passenger side is the same measurements as the drivers side, so if you've done one side you can use it as a guide for the other.

The B-Pillars (shiny black plastic)? they just pop off, open the door, stick a flat headed screwdriver behind them and pop them off. As for affix new ones depends on what your doing. Most people just wrap the old ones and pop them back on.

I got mine from Tarmac, there were no markings, Tarmac just supplied just measurements. It was a group buy on here earlier in the month. If you search for the group buy and post there someone might still have the instructions lying around or you could just ask Tarmac for them. The easiest thing to do is just take off the OEM skirt and use it as a guide. One piece of advice make the holes you drill longer along the length so you have some wiggle room.

They are not circular caps, they have 2 pegs. If you took the Nissan badge of the cap in your link and held it on with 2 pegs that's what I'm looking for.

Hi, I've lost the centre cap of one of my wheels can someone point me in the right direction for a replacement. I've got the old style GT (pre Rays) wheels, not sure what you guys call them!

Take a photo of their bumper as soon as they get back, it doesn't look like it will have done much but its still evidence.

I’ve got one for sale, links in my signature. I tried polishing the scratches out of one but it leaves you with a shiny strip, you can’t easily get it back to brushed aluminium look. I ended up buying a spare one that was dinged up polishing it out, not liking it going back to my old brushed one and then eventually painting the polished one gloss black. There are photos of the black one in build thread (link also in my signature).

There is a trader on here 'Hide & Seat' that will do leather recovers, but its not cheap.

I might use these later in the year for some internals, they seem to be the only place local to Brighton http://www.sussexhydrografix.co.uk/