Fluke
-
Posts
860 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Store
Posts posted by Fluke
-
-
Looks like a trip to B&Q then.
Wheres es the best place to feed the positive wire through to the battery? I can't see the grommet where the cars wiring loom goes into the cabin, anyone got a picture?
-
Seats are out along with the interior trim and I have just finished lining out the sub enclosure with 2 layers of dynomat.
I now now need to figure out how to attached the sub to the mounting plate, as there is not enough room around the edges to put screws, there's a 1/4 inch gap all the way round. Any ideas?
-
Send your parts to them, here is the web site for more info http://www.aquagraphix.co.uk.
I just bought spare parts and sent them away to be done, this saves any inconvenience whilst waiting with the added benefit of being able to put your car back to standard when it comes to selling. You can then sell your dipped parts on separately.
-
What was the cost?
-
With lots of advice from OV53 about what kit to get, I have finally got a weekend off work so that I can install this little lot.
I plan on using the stock sub position and will seal it with dynomat, hopefully the Hertz ES250.5 sub will work nicely there. The Alpine PDX-9 5 Chanel amp should fit nicely into the cubby behind the passenger seat, the Morel Tempo coax will go into the rear speaker pods and the Tempo 2 ways should sound great in the doors.
I have plenty of dynomat to cover the door speaker areas, is it worth putting some inside on the door skin itself?
I have 14 awg Stinger pro speaker wire, to run down each side of the car doors and my plan was to run RCA leads from the head unit down one side of the transmission tunnel and the power to the sub down the other side. Does that sound ok?
I have a little experience with ICE, but this is my first go at a decent install, so any advice would be most welcome.
-
Everyone is robbing my gold carbon weave now
Looks good mate
Aqua graphics are extremely good also. Same people that did mine.
Aquagrahpix are the people to go to. I have some more stuff with them being dipped right now. The gold carbon weave looks fantastic and I had considered getting the console covering the transmission tunnel dipped as well.
-
Interested in the exhaust, engine brace and lip. Do you have any better pictures of the lip?
-
As per the title I am looking for a carbon engine cover for a DE, like this one sold by Heff a few months ago.
-
Thanks.
-
I want to tap into the fuel pump electrical wiring so that I can fit a fuel cut off switch operated by a tracker and relay. Does anyone have a wiring diagram? I was hoping that whilst swapping out my subwoofer this weekend, I could access the fuel pup wiring?
-
I wouldn't mind a set for a DE, do they come in orange?
-
-
You need to hook up the power antenna, I put a post about it on here with pictures. I will see if I can dig it out.
-
I installed my new 8500bt into my 350z and can't seem to get my rear camera working. The camera worked perfectly when used with my Appradio.
I have the signal wire from the reverse light attached to the purple/white wire on the head unit and have tried playing with the head unit swapping from ground to battery in the head unit options, but still can't get the camera working?
Any ideas?
-
coughI've got a 3 piece kit that I could be convinced into letting go - I just haven't fitted it yet as nobody likes orange...Send me a PM if interested
Sent from my iPhone using Tapatalk
???
-
I had the parts pictured in my build thread done by http://www.aquagraphix.co.uk/ they did a stunning job, the finish was outstanding.
-
PM ZmanAlex, theres a post on painted callipers, apparently he did a set in Ultra Yellow for someone on the forum here ... Outstanding so they are...
Thanks, but I want them redone in the same gold colour.
-
Here is a link to my first attempt.
http://www.350z-uk.com/topic/79018-dipped-interior-and-tablet/
-
I will get a few more picture up when I get a few mins.
Wls350 - My tablet is hooked up to my Pioneer AVH 8500bt, using a HDMI lead. How have you got got sound to your HU for Nav instructions?
-
a member on this forum - Vlad - has just set up his own dipping business would be a good bet for anyone on here wanting dip services
Vlad isn't isn't dipping any longer.
-
I am looking at dressing up my engine bay, but cant seem to find a source for the orange radiator hose kits. Can somebody point me in the right direction?
-
Are these still available? If so can you PM me PayPal payment details?
- 1
-
I changed mine whilst swapping over the discs, thinking that newer shoes would improve the handbrake efficiency.... Easy job, but made bugger all difference.
-
Thanks for the replies, Is it easy to remove? I can get it sand blasted powder coated very cheaply.
ICE install starts today - Any advice?
in I.C.E & Electronics
Posted
behind the battery?