lmc

In my old rx7 I ran a 10.15 with 145mph terminal speed

Just measured and from the wheel to the outside edge of the arches is 48mm so to get your wheels to there would require 61mm spacers. I know you don't want to sit out that far so all you need to do is reduce the spacers to where you want your wheels to sit. Like i said earlier all arches are slightly different so just take this as a rough guide.

What ET were your alloys that were on yesterday lee? they are similar to the wheels im putting on and they didnt look like they needed to be pulled out 5cms With the spacers on they are 10.5 et 5 so 13 mm further out than yours. Roughly to sit where you were talking about would require another 35/40 mm spacer. Im home in 10 mins so can take a measurement for you.

Fronts will need about 15/20 Rears about 50 That said it will all depend on the width of the new arches as theyall vary slightly.

Nothing to do with me but Saw these on ebay earlier http://www.ebay.co.uk/itm/kw-st-nissan-350z-coilovers-/192093325482?hash=item2cb9a788aa:g:aDwAAOSw2xRYX9I6

Is it fitted yet??? lol

Pm,d

thanks does have the archs on tho but yer it does look nice without but had to do the whole lot, tho had i been told how much of a pain it is i may have stopped and left it without them.... its getting there got the front passenger arch left half to get on and spoiler, the drivers rear by the petrol cap needs a fair bit of taking out sadly ... another couple weeks should be a done job what are you planing to use in between the arches and the car...a 3m weathershield strip or something similar?also what did you use to extend the splash guards? If your on about extending the inner plastic arches what i did with my rx7 was to get a roll of 2mm abs plastic of ebay. It molds really easy with heat then i just used an industrial stapler to fix to existing arch.

Looking good mate. Just wheels to go?

Im guessing fsb means front strut brace

Looks like a squashed renault megane

thanks Lee...how is your project going? Slowly mate. Only got a single garage so need the weather to be ok so i can work on the drive, hence why im very envious of your space.

Good progress looking forward to seeing the end result.

These are non led version sorry. You need to look for 2006+ for led. Yes realised that just after I posted. Anyway glwts

Are these the led ones? If so can i call dibs?

Needs to bemade to fit my apexi exhaust. Not the same as oem unfortunately.

It's alright now 95% of the hardworks been done lol

Judging by the lack of communication Im guessing there was at least 1 ahead in the que

In fact just noticed your only up the road from me so could pick up anytime.

I'll take the rear lights if still available.

Bump.. Nobody going back to stock before thet sell up???

Luckily it's not my first attempt at fitting a wide kit and it was only my own time so not paying somebody else to do it for me. That said it took so long to do it i lost the love for the veilside kit and have sold it all minus the arches which im cutting/ reshaping to suit myself.

^^^^^ WHERE ???? ^^^^^ As I'm looking for it too !!! Although I'm searching for a"Urethane" one and not "fibreglass" ������ you do realise you have replied to a post from 4 years ago good luck with the search anyway yeah- sorry ������Always knew that I was a bit slow, lol ������������ It's just that I've been a bit"balls out", while searching the internet for the VS3 style kit over the past few months- and this thread became Highlighted. And I thought by posting a reply to this thread, would've bumped it up to get attention again ������������ I've just ordered the AIT VS3 kit through Mad Motors - but will take 10weeks for delivery, , , , so at least the winter will be gone - then I can get a bit"Blingy" for the Summer ������������������������ Perry If i was you id cancel the order. I bought the same kit and the fit is crap. Ive put around 120 hours into getting it to fit right.

Great progress mate

I think that's Docwra,s old car