Keyser

I'll give you £5 help a starving man out and all that.

You been giving yourself a Stranger as well then Perv Why didn't I think of that earlier

Been manic here lately Got to change a gearbox on a Zed at the weekend, a meet on Wednesday evening, but thought I'd better get the Mini moved on a bit as well 21 Weekends to go So thought I'd have a go at the roll cage tonight as the ZedShed is empty Started with something easy ends rounded Then cleaning the paint of this Took some time and my hands gone numb but Some bits to neaten up as although it's a proper saftey cage it will be on show in a road car so .... Bit of welding and grinding we get More of the same soon Maybe a road trip tomorrow night as I won an eBay auction Stay tuned for the next exciting episode ......................

Well get on it then!

+ Lots I'm running a Vortech V2 with a few supporting mods on a built engine mate All in here if your bored for a few hours http://www.350z-uk.com/topic/52481-project-zee-business-all-change-17th-jan/

I'm at 468WHP without the NOS

You need the midlands branch "ZedShed" Wasso Just think if you had a polishing room that size

Well the more doughnuts I eat the worse the mpg

I get 6mpg on track 17 - 19 "normal road" plus 1l of deionised water per 100 miles

along Good luck with the hunt

I think it would be OK I just had one done and my mate had his supra wheel done, his was worse than that he was quoted £45 + VAT for the repair - must be someone near you that can sort it mate??? Hope you get it sorted

I have an idea for a colour .......................

If only I had seen this first - think of the money I could have saved Have to see the finish it gives before we decide which is "superior"

Ok GT4 we get the message

Black kitchens look awesome but like the cars a pain to keep clean.

I'll get some pics of my setup tomorrow for you. The BPV can come off the front of the plenum, the fuel reg I picked up with aT piece in the line to the fuel tank vapour trap release. When tuning we found that sharing the line to the vapour release and/or the BPV causes fluctuations In the pressure this makes it a pain to tune, I suffered because I have a Haltech and it has it's own sensor built in, if your going up rev I don't think it will matter but you may get a flick in the boost gauge. Worm gear or "jubilee" clips eBay will have, I get mine from a local supplier he has everything from about 6mm to 100mm I can post ya some if your really stuck.

I don't think Sam is gonna change his mind

Hmmm Is that reverse psychology ??? Confused

[subliminal message] GREEN [/subliminal message]

So true Mr G I think if he gets enough dis-likes he may do it I don't care, I'll spray them for him - I'm curious to see if his Zed will carry it off and its less boring than black or silver

Don't use them on the Vacum line just silicone hose of the correct size - they are vacum so they "suck" on - the threaded connector may leak - mine was/is fine - 45PSI to start when you dial it in BTW You don't have to put the vacum line on you can leave it open - but then you need higher pressure all the time to account for no increase - mine is set at 43psi idle on boost it goes to around 48psi "normal" driving around 45psi. For what it's worth I found there are 2 types of PTFE tape - one is for water pipes and not for use on fuel/oil etc the other is NOT for water pipes and is fine for engines etc - I used the same stuff that I got with my compressor air lines and never had a problem - may not be true But hate for it to disolve or something silly.

Nice pics - looks like "cold" fun

Oi Oi I shall be watching with intrest

It has been done - I don't think it's that bad!