Keyser

By Request

PM'd

Or this one and £5 left :thumbs: https://www.ebay.co.uk/itm/2006-Nissan-350z-6-Speed-Low-Mileage/163490182902?_trkparms=aid%3D888007%26algo%3DDISC.MBE%26ao%3D1%26asc%3D55677%26meid%3De2ea6beef9154eb19757b72a7f62b728%26pid%3D100009%26rk%3D1%26rkt%3D1%26sd%3D264157749395%26itm%3D163490182902&_trksid=p2047675.c100009.m1982

I think your problem is that there are 2 sizes of that lower ball joint but I'm not sure why or when they change so I don't know if it's a year thing or a JDM thing. I'd refer to @ZMANALEX maybe drop him a PM as he will most likely know if I'm right and be able to quote the part numbers without using the book Hope you get it sorted

along

I have to say I have never had one overflow from turning the wheels with the engine off, however it is most likely that it is the cause of the overflow. Simple to check though - start the engine and make sure everything works as it should and the levels are correct. Have the levels been topped up lately? its not uncommon to overfill the reservoirs which will cause this.

But has planning been rejected? I had 2 objections from neighbours (we have 6 properties that share boundaries with our house/plot) but planning was still granted so I have my fingers crossed for @SuperStu

If this guy does anything else to annoy the OP then Alex's next post .............

I got a mention for knowing where a plug went - engage smug mode Great job mate and as I said be fore good write up

Glad it's sorted

I was thinking I'd drop by - just to look at some Zed's I'll park at the other end of the car park

Lack of or to much?? Hope I'm right then your sorted

Look behind the shroud/panel - If I'm right then that wire passes through the panel and plugs into the expansion tube on the end of the air con condenser. Or the idiots guide - Thin shiny air con radiator has a pipe thing on the left end as you look at the car from the front. (drivers side) there is plug in the top of that pipe, your cable should fit that Hope that helps

Nice lap I think the GTR guy/gal?? just wanted to mess with your time he/she cost you a good few seconds on that lap!

OK It is now call Project Elrond Ref Legolas are you not getting confused with Smeagol Either way it still only counts as one Not sure if I'm Gandalf or Gimli

These are from an 04 plate 350z, look different to me. Might help

nice mate looks great

First time I went some guy tried to get on the ring with a tractor As the rest say the first lap is an experience, take it steady keep right, after you have done a couple of laps you get into the swing of it and relax then it gets fun Also Docwra is spot on Pistenklaus do a cracking steak Here he is

What he said Near Bournemouth, PM me it you want to sort a day to collect them

OK then, Stand by to cringe Now it was pointed out to me by someone that shall remain anonymous @andybp that I was basically building a 350z chassis from the ground up, this is all well and good but will it fit into the pop shell? Well the simple answer is no - not a hope in hell, did I let that slow me down? No So now I have front and rear suspension mounts made I got the shell off the old chassis and into the Zed Shed - a few measurements show that the bracing on it was not sufficient or stresses since they were fitted have caused it to bend out of alignment so add straightening it up again to the list of problems Anyway a few more measurements and the afore mentioned busy body and my suspicions proved correct - it aint gonna fit the body is to narrow for the new running gear! So I came up with a solution (some may say it's OTT) Bloody wide enough now isn't it So the theory is lay it over the suspension and fill in the gap in the middle Stay tuned to see how that goes Keyser Maximum Effort

No not at all - well maybe a little That slowed down the Pop project but not other antics so we are all good Hmmm you offered Humanitarian aid but The PM said we had a Brexit deal - Just saying neither have actually happened yet

Hi All Overdue update As i Have far too many projects and you lot seem to like seeing my antics I thought I'd just keep them all together I have done a bit on the pop I'm just not showing you lot yet as you will no doubt think I have lost the plot (spoiler - I have) Slowing down the Pop project is phase 1 of a top secrete project that @andybp is helping me out with However Phase 1 was completed when this arrived - Out with the old In with the new Spot the difference? No nor can I My Milling machine motor bearings are dying and the bed transverse feed is so worn it wobbles, The parts just for the motor were over £700 and then the bed would need work, I ended up chatting with a guy local to me that sells engineering equipment as well as servicing them he offered me a part exchange on mine which cost less than the parts (let alone labour) to repair mine. So that was a no brainer and I did the deal - just need to get it wired back in and I'm good to go Keyser Maximum Effort

Yes mate - they are holding a tarpaulin down Available to collect if you want them

looks good